Measuring your opening: Start with the right measurements.
Draft — not yet approved by the owner. Nothing on this page may be relied on. It stays a draft until the owner reviews and approves it.
This page is being prepared. Until it is published, send a support request from the help centre at /help with any question about measuring.
On this page
Measuring checklist
- Measure the finished openingTile, stone or panel to the same on the opposite side. Do not measure bare studs or backer board — the finished surface is what the glass meets.
- Take the width at three heightsTop, middle and bottom: near the top, at about mid-height, and near the floor or curb. Openings are rarely identical at all three.
- Keep the smallest widthWrite down all three figures and keep the smallest. A door ordered to the widest figure will not pass the narrowest point.
- Measure the height on both sidesFrom the finished floor, curb or sill to where the top of the glass will sit.
- Check walls and sillCheck the walls for plumb and the curb or sill for level with a spirit level, and note how far out they are.
- Note anything in the wayA sloped ceiling, a window reveal, a shower valve, a bench, or a curb that is not flat on top.
- Confirm the product requirementsEach door lists its own fitting range and requirements — see what the sample catalog covers.
Write your figures here
In inches, from the finished surfaces. Decimals are fine.
Enter at least one width to see the one to use.
Your own figures, not checked by us. Not a fit approval.
Follow the manufacturer's measuring instructions.
Every product can have its own requirements. This is general guidance: it is not an installation instruction and it does not replace the supplier's own measuring sheet.
What the sample catalog covers
Meridian Frameless Double Sliding Door, 46–49″ W × 76″ H, Towel Bar & Finger Pull
Opening range 46–49 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 46–49 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 46–49″ W × 76″ H, Two Towel Bars
Opening range 46–49 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 46–49 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 46–49″ W × 76″ H, Two Finger Pulls
Opening range 46–49 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 46–49 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 50–55″ W × 76″ H, Towel Bar & Finger Pull
Opening range 50–55 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 50–55 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 50–55″ W × 76″ H, Two Towel Bars
Opening range 50–55 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 50–55 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 50–55″ W × 76″ H, Two Finger Pulls
Opening range 50–55 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 50–55 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 46–49″ W × 80″ H, Towel Bar & Finger Pull
Opening range 46–49 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 46–49 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 46–49″ W × 80″ H, Two Towel Bars
Opening range 46–49 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 46–49 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 46–49″ W × 80″ H, Two Finger Pulls
Opening range 46–49 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 46–49 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 50–55″ W × 80″ H, Towel Bar & Finger Pull
Opening range 50–55 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 50–55 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 50–55″ W × 80″ H, Two Towel Bars
Opening range 50–55 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 50–55 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 50–55″ W × 80″ H, Two Finger Pulls
Opening range 50–55 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 50–55 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 76″ H, 58″ Nominal, Towel Bar & Finger Pull
Opening range 56–60 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 76″ H, 58″ Nominal, Two Finger Pulls
Opening range 56–60 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 72″ H, Towel Bar & Finger Pull
Opening range 56–60 in wide, 72 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 72 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 72″ H, Two Towel Bars
Opening range 56–60 in wide, 72 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 72 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 72″ H, Two Finger Pulls
Opening range 56–60 in wide, 72 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 72 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 76″ H, Towel Bar & Finger Pull
Opening range 56–60 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 76″ H, Two Towel Bars
Opening range 56–60 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 80″ H, 58″ Nominal, Towel Bar & Finger Pull
Opening range 56–60 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 80″ H, 58″ Nominal, Two Finger Pulls
Opening range 56–60 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 80″ H, Two Towel Bars
Opening range 56–60 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 80″ H, Two Finger Pulls
Opening range 56–60 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 61–65″ W × 76″ H, Towel Bar & Finger Pull
Opening range 61–65 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 61–65 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 61–65″ W × 76″ H, Two Towel Bars
Opening range 61–65 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 61–65 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 61–65″ W × 76″ H, Two Finger Pulls
Opening range 61–65 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 61–65 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 66–72″ W × 76″ H, Towel Bar & Finger Pull
Opening range 66–72 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 66–72 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 66–72″ W × 76″ H, Two Towel Bars
Opening range 66–72 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 66–72 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 66–72″ W × 76″ H, Two Finger Pulls
Opening range 66–72 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 66–72 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 61–65″ W × 80″ H, Towel Bar & Finger Pull
Opening range 61–65 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 61–65 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 61–65″ W × 80″ H, Two Towel Bars
Opening range 61–65 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 61–65 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 66–72″ W × 80″ H, Towel Bar & Finger Pull
Opening range 66–72 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 66–72 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 66–72″ W × 80″ H, Two Towel Bars
Opening range 66–72 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 66–72 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 66–72″ W × 80″ H, Two Finger Pulls
Opening range 66–72 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 66–72 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 80″ H, Acid-Etch Glass, Towel Bar & Finger Pull
Opening range 56–60 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 80″ H, Acid-Etch Glass, Two Towel Bars
Opening range 56–60 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 80″ H, Acid-Etch Glass, Two Finger Pulls
Opening range 56–60 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 80″ H, Gray Glass, Towel Bar & Finger Pull
Opening range 56–60 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 80″ H, Gray Glass, Two Towel Bars
Opening range 56–60 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 80″ H, Gray Glass, Two Finger Pulls
Opening range 56–60 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 80″ H, Optiwhite Glass, Two Towel Bars
Opening range 56–60 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 80″ H, Optiwhite Glass, Two Finger Pulls
Opening range 56–60 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 66″ H, Towel Bar & Finger Pull
Opening range 56–60 in wide, 66 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 66 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 66″ H, Two Towel Bars
Opening range 56–60 in wide, 66 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 66 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 66″ H, Two Finger Pulls
Opening range 56–60 in wide, 66 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 66 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 61–65″ W × 66″ H, Towel Bar & Finger Pull
Opening range 61–65 in wide, 66 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 61–65 | Not verified |
| Height (in) | 66 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 61–65″ W × 66″ H, Two Towel Bars
Opening range 61–65 in wide, 66 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 61–65 | Not verified |
| Height (in) | 66 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 66–72″ W × 72″ H, Towel Bar & Finger Pull
Opening range 66–72 in wide, 72 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 66–72 | Not verified |
| Height (in) | 72 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 66–72″ W × 72″ H, Two Towel Bars
Opening range 66–72 in wide, 72 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 66–72 | Not verified |
| Height (in) | 72 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 66–72″ W × 72″ H, Two Finger Pulls
Opening range 66–72 in wide, 72 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 66–72 | Not verified |
| Height (in) | 72 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 66″ H, Optiwhite Glass, Towel Bar & Finger Pull
Opening range 56–60 in wide, 66 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 66 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 66″ H, Optiwhite Glass, Two Towel Bars
Opening range 56–60 in wide, 66 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 66 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 66″ H, Optiwhite Glass, Two Finger Pulls
Opening range 56–60 in wide, 66 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 66 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 66″ H, Gray Glass, Towel Bar & Finger Pull
Opening range 56–60 in wide, 66 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 66 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Meridian Frameless Double Sliding Door, 56–60″ W × 66″ H, Gray Glass, Two Finger Pulls
Opening range 56–60 in wide, 66 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 66 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Horizon Frameless Sliding Door, 46–49″ W × 76″ H
Opening range 46–49 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 46–49 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Horizon Frameless Sliding Door, 50–55″ W × 76″ H
Opening range 50–55 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 50–55 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Horizon Frameless Sliding Door, 46–49″ W × 80″ H
Opening range 46–49 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 46–49 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Horizon Frameless Sliding Door, 50–55″ W × 80″ H
Opening range 50–55 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 50–55 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Horizon Frameless Sliding Door, 56–60″ W × 72″ H
Opening range 56–60 in wide, 72 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 72 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Horizon Frameless Sliding Door, 56–60″ W × 76″ H
Opening range 56–60 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Horizon Frameless Sliding Door, 56–60″ W × 80″ H
Opening range 56–60 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Horizon Frameless Sliding Door, 56–60″ W × 84″ H
Opening range 56–60 in wide, 84 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 84 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Horizon Frameless Sliding Door, 61–65″ W × 76″ H
Opening range 61–65 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 61–65 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Horizon Frameless Sliding Door, 66–72″ W × 76″ H
Opening range 66–72 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 66–72 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Horizon Frameless Sliding Door, 61–65″ W × 80″ H
Opening range 61–65 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 61–65 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Horizon Frameless Sliding Door, 66–72″ W × 80″ H
Opening range 66–72 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 66–72 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Horizon Frameless Sliding Door, 56–60″ W × 80″ H, Acid-Etch Glass
Opening range 56–60 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Horizon Frameless Sliding Door, 56–60″ W × 80″ H, Gray Glass
Opening range 56–60 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Horizon Frameless Sliding Door, 56–60″ W × 80″ H, Optiwhite Glass
Opening range 56–60 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Horizon Frameless Sliding Door, 56–60″ W × 66″ H
Opening range 56–60 in wide, 66 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 66 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Horizon Frameless Sliding Door, 56–60″ W × 66″ H, Optiwhite Glass
Opening range 56–60 in wide, 66 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 66 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Tide Frameless Sliding Door, 46–49″ W × 76″ H
Opening range 46–49 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 46–49 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Tide Frameless Sliding Door, 50–55″ W × 76″ H
Opening range 50–55 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 50–55 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Tide Frameless Sliding Door, 46–49″ W × 80″ H
Opening range 46–49 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 46–49 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Tide Frameless Sliding Door, 50–55″ W × 80″ H
Opening range 50–55 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 50–55 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Tide Frameless Sliding Door, 56–60″ W × 76″ H
Opening range 56–60 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Tide Frameless Sliding Door, 56–60″ W × 80″ H
Opening range 56–60 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Tide Frameless Sliding Door, 61–65″ W × 76″ H
Opening range 61–65 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 61–65 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Tide Frameless Sliding Door, 61–65″ W × 80″ H
Opening range 61–65 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 61–65 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Tide Frameless Sliding Door, 66–72″ W × 80″ H
Opening range 66–72 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 66–72 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Tide Frameless Sliding Door, 56–60″ W × 66″ H
Opening range 56–60 in wide, 66 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 66 | Not verified |
| Glass thickness (mm) | 10 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Harbor Framed Double Sliding Door, 50–55″ W × 76″ H
Opening range 50–55 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 50–55 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 6 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Harbor Framed Double Sliding Door, 56–60″ W × 72″ H
Opening range 56–60 in wide, 72 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 72 | Not verified |
| Glass thickness (mm) | 6 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Harbor Framed Double Sliding Door, 56–60″ W × 76″ H
Opening range 56–60 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 6 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Harbor Framed Double Sliding Door, 61–65″ W × 76″ H
Opening range 61–65 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 61–65 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 6 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Harbor Framed Double Sliding Door, 66–72″ W × 76″ H
Opening range 66–72 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 66–72 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 6 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Harbor Framed Double Sliding Door, 56–60″ W × 66″ H
Opening range 56–60 in wide, 66 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 66 | Not verified |
| Glass thickness (mm) | 6 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Harbor Framed Double Sliding Door, 56–60″ W × 60″ H
Opening range 56–60 in wide, 60 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 60 | Not verified |
| Glass thickness (mm) | 6 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Harbor Framed Double Sliding Door, 56–60″ W × 58″ H
Opening range 56–60 in wide, 58 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 58 | Not verified |
| Glass thickness (mm) | 6 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Keel Framed Double Sliding Door, 48″ W × 76″ H, Towel Bar & Finger Pull
Opening range 48 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 48 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 8 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Keel Framed Double Sliding Door, 46–49″ W × 76″ H, Two Towel Bars
Opening range 46–49 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 46–49 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 8 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Keel Framed Double Sliding Door, 50–55″ W × 76″ H, Two Towel Bars
Opening range 50–55 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 50–55 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 8 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Keel Framed Double Sliding Door, 56–60″ W × 76″ H, Two Towel Bars
Opening range 56–60 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 8 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Keel Framed Double Sliding Door, 61–65″ W × 76″ H, Two Towel Bars
Opening range 61–65 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 61–65 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 8 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Keel Framed Double Sliding Door, 66–72″ W × 76″ H, Two Towel Bars
Opening range 66–72 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 66–72 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 8 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Keel Framed Double Sliding Door, 56–60″ W × 76″ H, Acid-Etch Glass, Towel Bar & Finger Pull
Opening range 56–60 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 8 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Keel Framed Double Sliding Door, 56–60″ W × 76″ H, Acid-Etch Glass, Two Towel Bars
Opening range 56–60 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 8 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Keel Framed Double Sliding Door, 56–60″ W × 66″ H, Acid-Etch Glass, Towel Bar & Finger Pull
Opening range 56–60 in wide, 66 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 66 | Not verified |
| Glass thickness (mm) | 8 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Keel Framed Double Sliding Door, 56–60″ W × 66″ H, Acid-Etch Glass, Two Towel Bars
Opening range 56–60 in wide, 66 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 66 | Not verified |
| Glass thickness (mm) | 8 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Pier Framed Double Sliding Door, 46–49″ W × 76″ H
Opening range 46–49 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 46–49 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 6 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Pier Framed Double Sliding Door, 50–55″ W × 76″ H
Opening range 50–55 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 50–55 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 6 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Pier Framed Double Sliding Door, 56–60″ W × 70″ H
Opening range 56–60 in wide, 70 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 70 | Not verified |
| Glass thickness (mm) | 6 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Pier Framed Double Sliding Door, 56–60″ W × 76″ H
Opening range 56–60 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 6 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Pier Framed Double Sliding Door, 56–60″ W × 80″ H
Opening range 56–60 in wide, 80 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 80 | Not verified |
| Glass thickness (mm) | 6 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Pier Framed Double Sliding Door, 61–65″ W × 76″ H
Opening range 61–65 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 61–65 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 6 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Pier Framed Double Sliding Door, 66–72″ W × 76″ H
Opening range 66–72 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 66–72 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 6 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Pier Framed Double Sliding Door, 56–60″ W × 60″ H
Opening range 56–60 in wide, 60 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 60 | Not verified |
| Glass thickness (mm) | 6 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Pier Framed Double Sliding Door, 56–60″ W × 66″ H
Opening range 56–60 in wide, 66 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 66 | Not verified |
| Glass thickness (mm) | 6 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Regatta Framed Triple Bypass Door, 46–49″ W × 76″ H, Left-Hand Opening
Opening range 46–49 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 46–49 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 8 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Regatta Framed Triple Bypass Door, 46–49″ W × 76″ H, Right-Hand Opening
Opening range 46–49 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 46–49 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 8 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Regatta Framed Triple Bypass Door, 56–60″ W × 76″ H, Left-Hand Opening
Opening range 56–60 in wide, 76 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 76 | Not verified |
| Glass thickness (mm) | 8 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
Regatta Framed Triple Bypass Door, 56–60″ W × 66″ H, Right-Hand Opening
Opening range 56–60 in wide, 66 in high, as the manufacturer lists it. Measure your finished opening and ask us before ordering if you are unsure.
| Requirement | Value | Status |
|---|---|---|
| Finished opening width (in) | 56–60 | Not verified |
| Height (in) | 66 | Not verified |
| Glass thickness (mm) | 8 | Not verified |
| Sill requirement | Unknown | Not yet verified for this sample catalog |
| Wall tolerance | Unknown | Not yet verified for this sample catalog |
| Opening clearance | Unknown | Not yet verified for this sample catalog |
A fitting range is an aid, not an installation approval. Confirm every figure with the supplier before ordering.
I haven't measured yet
You do not need measurements to browse, compare or save products.
When you are ready to measure, have to hand:
- A steel tape measure — a fabric one stretches.
- A spirit level, or a level app, for the walls and the curb.
- Somewhere to write three width figures and two height figures.
- A second person, if the opening is wider than your reach.
Ask a professional
Send the opening details you have and someone can look at them. This records a request — it does not book a visit, and nothing is scheduled.
More help
- Delivery
- Returns
- Warranty
- Sliding or hinged shower doors: how they differ
- Sliding doors for a bathtub or a walk-in shower
- Will this hardware fit my shower glass?
Still have a question?
Send a support request from the help centre. It is stored with a reference you can quote later.

